- How to set up hp laserjet 4100 series printer on network how to#
- How to set up hp laserjet 4100 series printer on network serial number#
- How to set up hp laserjet 4100 series printer on network drivers#
Press ITEM repeatedly until CFG TCP/IP = NO appears. It will appear as CFG NETWORK = NO each time this menu is accessed. Changing it to YES allows the settings to be changed at that time. NOTE: The CFG NETWORK = XXX (XXX being YES or NO) is a toggle, not a permanent setting.
Press the PLUS or VALUE button until CFG NETWORK = YES appears. Press the ITEM button until CFG NETWORK = NO appears. Press the MENU button until HP MIO 1 (or 2), or HP EIO 1 (or 2) appears. To configure TCP/IP parameters from the control panel, use the following instructions:
How to set up hp laserjet 4100 series printer on network serial number#
The HP on line chat won't let me log in and hold a chat with HP unless I know the Serial Number of the printer, which I don't have here at home.HP LaserJet 4000, 4050, 4100, 4500, 4550, 5Si, 5SiMX, 5000, 5100, 8500, 8550, 8000, 8150 printers, HP 2500c Professional series, HP Business Inkjet 2200, 2250, and 2600 printers ctID=c01664444&jumpid=reg R1002USEN ) and another page I found says that it is not supported ( One page I found says the printer is supported ( It's as if the firmware in the 4100 just doesn't have something in it's lexicon that Snow Leopard needs.
How to set up hp laserjet 4100 series printer on network how to#
Sorry, I'm home right now and don't have direct access to the printer so I can't give you the precise language of the message, but the gist of the message is that the system tried to connect to the printer to send the print data but the printer does not know how to respond to the command that was sent. When I try to print, my print job appears in the queue as expected, than an error appears that something about a "bad command". I can set up the printer(s) just fine in the Print & Fax Preference and Snow Leopard finds the printer just fine when I enter the IP address and chooses the correct HP Driver. I have two HP 4100dtn printers on ethernet. If I connect the 4100 Ethernet cable to the Ethernet hub, the supply level does not show nor can I print. Status: If I connect the 4100 Ethernet cable directly to the back of the iMac, the “Supply” level indicates the true level of toner in the 4100. However, it does not show up in the “Add Printer” window under “default” or anywhere else. When this is done, the printer shows up when you give a print command. I tried this two ways: in the “Add Printer” window under “IP,” inputted as the IPP, and inputted as the HP Jetdirect Socket (as per the HP instructions). According to HP website, since Apple Talk no longer exists, we are required to input the IP for the device. None of the three people I worked with at Apple could help and the HP representative was unsure if they could help but that it would cost me $40 to find out. I’ve contacted HP and Apple about this problem.
It is connected to an AT&T 2-Wired Ethernet Hub/DSL Modem (model 2701HG-B) that is connected to the iMac. It only has Ethernet and serial port outlets. I also have an older HP Laserjet 4100 which has been my steady workhorse for years.
How to set up hp laserjet 4100 series printer on network drivers#
Although initially scanning did not work with the J5750, I was able to make that work once additional drivers were downloaded from HP. Two devices: HP Color Laserjet 5550 and HP Officejet J5750 are connected to the iMac through a USB Hub. My set-up: new 24” iMac, many hard drives and more. Since I’ve installed Snow Leopard, I have not been able to print with my HP Laserjet 4100.
0 kommentar(er)
